This repo contains a bunch of tip/tricks I use in my Unifi setup. I should note that I'm running the USG Pro. Sorry for how unformal it is, this is mostly just a guide for me so I remember what I change :)
Below is a list of custom software I run on my USG
- Nano (because I can never remember Vi bindings 😂)
- DDNS (custom setup w/ cloudflare)
- DNScrypt (for DoH)
- Wireguard
To make use of a custom config.gateway.json file you'll need to connect to your controller. In my case I'm using the unifi-controller docker container in Unraid. For the case of this continer the config will exist at <appdata_path>/data/sites/<site_name>/config.gateway.json. Whenever this file is modified you can force the USG to re-provision with the new settings via the controller. Before re-provisioning use a JSON validator to ensure you are passing valid JSON. The USG really doesn't like being re-provisioned with an invalid configuration and this may soft-brick your router requiring a factory reset.
Some of the steps below will require the ability to install packages. To do so you'll need to add the following to your config.gateway.json:
{
"system":{
"package":{
"repository":{
"wheezy":{
"components":"main contrib non-free",
"distribution":"wheezy",
"url":"http://archive.debian.org/debian"
}
}
}
}
}
Once this is done, force re-provisioning and then SSH into your USG. Lastly run sudo apt-get update to fetch the package lists.
Note: Never do a bulk upgrade (e.g. apt-get upgrade) as this can soft-brick the router requiring a factory reset to fix it.
See the update.sh script in this repository. I recommend saving this script to /config/scripts/update/update.sh
It will automatically download and install dnscrypt-proxy, wireguard, ddclient as well as a few utilities such as nano and dnsutils.
Assuming you've followed the steps above to setup the package repository all you need to do is SSH into your USG and run sudo apt-get install nano.
I've got servers running from within my network as well as a VPN so I use DDNS to update my cloudflare DNS records auto-magically. Unfortunately the built-in DDNS client doesn't support cloudflare's new API - so we need to manually update the ddclient version. I was able to follow the instructions on ubnt wiki to set this up.
- SSH into your router and switch to root via
sudo -i - DDClient depends on a library, to install it you'll need to do:
apt-get update && apt-get install libdata-validate-ip-perl - Next install the latest ddclient (3.9.1 at the time of writing):
curl -sL https://raw.githubusercontent.com/ddclient/ddclient/6ae69a1ce688e8212b0973867b16af37f85172ef/ddclient -o /usr/sbin/ddclient
Now you'll need to setup your USG configuration file:
{
"service":{
"dns":{
"dynamic":{
"interface":{
"<WAN_INTERFACE>":{
"service":{
"cloudflare":{
"host-name":[
"<HOSTNAME_TO_UPDATE>"
],
"login":"<CLOUDFLARE_LOGIN>",
"options":[
"zone=<CLOUDFLARE_DOMAIN>"
],
"password":"<CLOUDFLARE_PAT>",
"protocol":"cloudflare"
}
}
}
}
}
}
}
}
Be sure to update all of the configuration variables here. To get your WAN_INTERFACE you can use the command show interfaces on the USG and the interface with your public IP is the one you want to put here. Lastly re-provision your USG with the new config.
To test you can use update dns dynamic interface <WAN_INTERFACE> and to validate that the DDNS worked successfully you can use show dns dynamic status
I've got an interesting DNS setup at home. Essentially I route all traffic through my USG which routes it through PiHole running on a separate server and then back to the USG for DNScrypt. I've got dnscrypt-proxy being used to route DNS via DNS over HTTPS to various resolvers, with the primary being cloudflare.
Installation is pretty straightforward. Essentially to need to download the binary and setup the configs. Here are some step by step instructions:
- SSH into your USG and switch to root using
sudo -i - Make the dnscrypt directory
mkdir /otp/dnscrypt - Set perms
chmod 777 /opt/dnscrypt/ - navigate to that dir
cd /opt/dnscrypt - Download the latest
dnscrypt-proxy-mips64binray from dnscrypt/dnscrypt-proxy usingcurl -sL https://github.com/DNSCrypt/dnscrypt-proxy/releases/download/2.0.39/dnscrypt-proxy-linux_mips64-2.0.39.tar.gz -o dnscrypt.tar.gz - unpack the binary
tar -xvzf dnscrypt.tar.gz linux-mips64/dnscrypt-proxy - move the binary to the current dir
mv linux-mips64/* . - cleanup
rm dnscrypt.tar.gz && rm -r linux-mips64 - make the dnscrypt binary executable
chmod +x dnscrypt-proxy - set ownership
chown root:root dnscrypt-proxy - Upload the config from this repo
dnscrypt/dnscrypt-proxy.tomlto/config/dns/dnscrypt-proxy.toml- This will have DNSCrypt running on port
5053- the USG runs dnsmasq on 53 so you can't run there - I use the following resolvers: ['cloudflare', 'quad9-dnscrypt-ip4-filter-pri', 'dnscrypt.ca-1-doh']
- I use the following fallback resolvers: ['1.1.1.1:53', '8.8.8.8:53', '9.9.9.9:53']
- This will have DNSCrypt running on port
- Lastly, setup dnscrypt as a service
./dnscrypt-proxy -config /config/dns/dnscrypt-proxy.toml -service install- This will set dnscrypt as a service which will work across reboots
- If you change the config use
sudo service dnscrypt-proxy restart
You will need to make sure /config/dns/dnscrypt-proxy.toml is setup. If not you can follow the instructions from the installation section to setup the configuration file.
I like to have all of my DNS traffic routed through DNScrypt and my PiHole which is running on another server. It even works for those pesky IoT devices which are hardcoded for their own DNS servers. Essentially DNS traffic in my setup looks like this:
Device -> USG (nat rule) -> PiHole -> USG (port 53) -> dnscrypt (port 5053)
To setup the NAT rule as well as the DNSMasq options you can add the following to your config.gateway.json. Note in the forwarding options I set strict-order followed by specifying the servers below. The ordering of the servers is actually reversed! It will attempt to use the from the bottom up.
{
"service":{
"forwarding":{
"options":[
"host-record=unifi,10.10.10.1",
"ptr-record=1.10.10.10.in-addr.arpa,Guardian",
"no-resolv",
"strict-order",
"stop-dns-rebind",
"bogus-priv",
"expand-hosts",
"domain-needed",
"server=1.0.0.1",
"server=1.1.1.1",
"server=<USG_IP>#5053",
"server=<PIHOLE_IP>#<PIHOLE_PORT>"
]
}
},
"nat":{
"rule":{
"1":{
"description":"Redirect DNS queries LAN",
"destination":{
"port":"53"
},
"source":{
"address":"!<USG_IP>"
},
"inside-address":{
"address":"<LAN_NETWORK>"
},
"inbound-interface":"eth0",
"protocol":"tcp_udp",
"type":"destination"
}
}
}
}
}
Lastly, all that's required is that you force re-provision your USG. To test you can use DNSleaktest to ensure you're using the servers you specified. If that's the case your DNS traffic will be encrypted and only these servers can see your requests. This is even the case for devices with hardcoded DNS (e.g. Alexa echo devices).
Credits to this tutorial for helping me get it set up in the first place.
- SSH into your USG and switch to the root account via
sudo -i - Install the correct wireguard package from wireguards/vyatta-wireguard
curl -sL https://github.com/WireGuard/wireguard-vyatta-ubnt/releases/download/<version>/wireguard-<board>-<version>.deb -o wg.deb
dpkg -i wg.debto install wireguard
Next we'll setup the auth configuration:
- Make the configs directory
mkdir /config/auth/wireguard - Setup permissions on the directory
chmod 777 /config/auth/wireguard - Generate the wireguard server keys
wg genkey | tee wg_private.key | wg pubkey > wg_public.key - Generate the client keys
wg genkey | tee client1_private.key | wg pubkey > client1_public.key- You'll need to do this for each client you have
- Now you need to update your
config.gateway.jsonwith the following information:
{
"firewall":{
"group":{
"network-group":{
"remote_user_vpn_network":{
"description":"Remote User VPN subnets",
"network":[
"<WIREGUARD_IP_RANGE>/24"
]
}
}
}
},
"interfaces":{
"wireguard":{
"wg0":{
"description":"VPN for remote clients",
"address":[
"<INTERNAL_NETWORK_RANGE>/16"
],
"firewall":{
"in":{
"name":"LAN_IN"
},
"local":{
"name":"LAN_LOCAL"
},
"out":{
"name":"LAN_OUT"
}
},
"listen-port":"443",
"mtu":"1492",
"peer":[
{
"<CLIENT_PUBLIC_KEY>":{
"allowed-ips":[
"<CLIENT_IP>/32"
],
"persistent-keepalive":25
}
}
],
"private-key":"/config/auth/wireguard/wg_private.key",
"route-allowed-ips":"false"
}
}
}
}
Be sure to fill in the following variables:
WIREGUARD_IP_RANGE - The network range being used by the VPN for clients
INERNAL_NETWORK_RANGE - All of the internal networks the VPN should be able to reach
CLIENT_PUBLIC_KEY - The public key which identifies this client (contents of client1_public.key)
CLIENT_IP - The IP that the client should have when connecting with this public key
Note: if you plan to connect remotely you'll need to portforward 443 for UDP traffic on the WAN_OUT firewall rule. This can be done within the controller's interface.
Now you'll need to enter the client configs on your devices:
[Interface]
PrivateKey = <client1_private.key>
Address = <CLIENT_IP>/16
DNS = <USG_IP>
[Peer]
PublicKey = <wg_public.key>
Endpoint = <PUBLIC_IP/HOSTNAME>:443
AllowedIPs = 0.0.0.0/0
Alternativly you can create that configuration file on the server and save it as client.conf. Then use qrencode -t ansi client.conf to print out the config to QR which can easily be scanned by most wireguard apps. Note you'll need to install qrencode on the usg with apt-get install qrencode, provided you have the repo setup as seen in the custom config section.
Once you connect to the VPN should see that your internal IP is the one specified by the wireguard VPN and your public IP is the one of your USG.
When updating everything in the /opt directory will be reset and all applications will be uninstalled. Before proceeding with the upgrade I recommend backing up your DNScrypt config (/config/dns/dnscrypt-proxy.toml) as well as your wireguard configs (/config/auth/wireguard). I should note that the wireguard configs will survive the upgrade but I would recommend backing up everything just in case. It's okay that the config.gateway.json is still customized during the upgrade, this won't break anything. After the upgrade is complete all you need to do is follow the steps for each application above to re-install the application.
To automate the upgrade process, after the update has completed you will noticed that the USG will be sitting in a "provisioning" state. That's because the usg doesn't have the wg0 interface. Simply run the update script /config/scripts/update/update.sh to re-install the required software which will re-create the interface.
Renew IP
disconnect interface pppoe2
connect interface pppoe2
Renew DDNS
show dns dynamic status
update dns dynamic interface pppoe2
Feel free to open an issue! I'll do my best to answer question there.